Hawking-technology HGS24S Manual do Utilizador

Please place main product photo here. 1

3.1 PHY Monitoring and Port Mode Setup One of the software’s major tasks is to continuously monitor the PHYs in order to set up the switch ports a

This section instructs you on how to enter and set up the configurations, which can be accessed by RS-232 serial port (out-of-band) on the rear pane

In-Band Connections (Web Browser / Telnet) To manage the switch through in-band access, you should configure the management station with an IP addr

4.2 Homepage On the Home page, you can select what you would like to configure by clicking the menu tabs located at the top of the homepage. They

To restore the default values of switch, click the “Default” button at the top of the homepage. If you want to reboot the switch, click the “Reboot

4.2.1 System To set up the system configurations such as login values, time-out values, and for enabling the VLAN Management:

Note: After you change the IP address, the switch will reboot itself. You may click the new address to link the New IP Address with your browser.

Items Functions Link Shows the status of each port. When it is red, it means the connection is down. Otherwise, it is green. Mode Choose the Sp

PVID When the VLAN-enabled switch receives a tagged packet, the packet will be sent to the port’s default VLAN according to

19

FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. Th

4.2.4 Aggregation/Trunking Configuration To set up the Port trunk groups, put the port numbers into the same Aggregation group line. There are eigh

4.2.5 Qos There is one mode of Quality of Service to choose: custom TOS. 4.2.5.1 Quality of Service (QoS) TOS Configuration To imp

4.2.5.2 QoS Port Shaper To control the port data’s flow rate, select “Enable” and enter the value you need from 250 - 1000000K

4.2.5.3 QoS Port Policer To control the port data’s flow rate, select “Enable” and enter the Value you need from 250 - 1000000K bps. If the packet

4.2.6 Mirror Port mirror is used to mirror traffic from a source port to a target port for analysis. Only 2 ports can be monitored (mirrored) simu

4.2.7 Statistics To check the status of port traffic, click the “Statistic” tab. You can click the “Clear” button to erase all records or click “R

4.2.9 Default To restore to default values, 1. Click the default button on the homepage. 2. Click “Yes” to restore default values. Do not power of

Standard IEEE802.3 10BASE-T IEEE802.3u 100BASE-TX IEEE802.3x full-duplex operation and flow control IEEE802.3ab 1000BASE-T IEEE802.1Q VLAN intero

Unpacking the Switch 4 Introduction 1.1 General Description 5 1.2 Gigabit Ethernet T

The complete HGS24S package consists of: • One HGS24S 24-Port 10/100/1000M Web-Smart Switch • Rack mount kit: 2 mounting brackets and screws • F

1.1 General Description The device is a 24-port 10/100/1000Mbps Ethernet Web-Smart Switch. Compared with traditional 10/100Mbps Ethernet, the swit

1.3 Key Features • 24 fixed 10/100/1000Mbps Gigabit Ethernet ports • Provides Auto-discovery Function for easy network management • Provides 8K

Wiring for 10/100/1000Mbps (Copper) Below is the summary of the cabling required: Media Speed Wiring 10Mbps Category 3,4,5 UTP/STP 100Mbps Categor

This switch can be placed directly on your desktop, on the floor, or mounted in a rack. Users can immediately use most of the features simply by at

2.3 Installing Network Cables Station Connections Refer to the wiring statement of the previous section; connect each station/device to the switch